Top double surface planer wholesale supplier

Double side planer manufacturer and supplier with V-hold Machinery: The defining characteristic of all machine presses is that they press a work-piece using high pressure to change its shape. While the exact mechanics vary depending on the type of machine press, most machine presses work by pressing a plate or die onto or against a work-piece. The work-piece can either be manually placed into the machine or a through-feed will automatically place the work-piece in the correct position. Once in position, using hydraulics pressure, the machine press pushes the plate or die against the surface of the work-piece, which causes the work-piece’s shape to deform into the shape required by the manufacturer. Find more details at double side planer.

The radial arm saw is pretty much a portable circular saw that glides on an adjustable arm suspended over a fixed cutting surface. The blade and motor are connected to the arm by a yoke, which is adjustable along both horizontal and vertical planes, enabling the saw to be swung in a variety of directions. For cross-cut work, position the board flush with the fence at the rear of the saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles. You can set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitring, or turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. As an example a model using a 10 inch blade would be able to cut work-pieces up to 3 inches thick.

A typical hydraulic down-acting press uses a pair of hydraulic cylinders, one on each end, to generate the tonnage required for the down stroke of the machine. Traditionally, these machines have a C or O frame profile design. With both types, when facing the front of the machine the hydraulic cylinders are located on the left and right hand side of the upper beam. Since the upper beam is being pushed down and up with hydraulic power, the upper beam will fall during a power outage and could create an unsafe environment. Down acting presses are commonly blocked at night to take pressure off of the hydraulic system. The lower beam does not move during bending so the operator will not get feedback that the brake is engaged.

A jointer is used for planing straight edges and surfaces of boards. In practice, it performs the work of a hand planer and is capable of producing a true surface with sufficient accuracy and speed. In consists of a frame, table, feed rollers, revolving head fitted with two or three cutter knives. With the help of feed rolls, the plank is fed to the cutter head which removes the wooden chips as the board advances and makes its surface smooth and plane. By means of an adjustable fence, the jointer can also be used for angular and level cuts. A jointer is specified by the length of the cutting blade.

Probably the second most important of single woodworking machines in a carpentry shop is the circular saw. It can be used for ripping, cross cutting, mitering, beveling, rabbeting, and grooving. Although there are many types of circular saws such as universal saw, variety saw, bench saw, the basic working parts are common to all. Each has a flat surface or table upon which the work rests while being cut, a circular cutting blade, cut-off guide, and a ripping fence that acts as a guide while sawing along the grains of the wood. The circular saw usually has provisions for tilting the table upto an angle of 45° to enable the machine to cut at different angles required during mitering, levelling, etc. The size of a circular saw is determined by the diameter of the saw blade.

A drill press is simply a fixed in place version of a hand drill, it’s great for precise work. With an adjustable table beneath the chuck with a hole in its centre, a spinning drill bit can pass cleanly through a work-piece. Drill presses come as either freestanding floor models or for worktops. The drill press is powered by an electric motor, driving it via a system of pulleys or gears. The drill bit is locked into the chuck, then driven down using a hand powered lever system, and a spring pushes it back up when pressure on the lever is released. A number of adjustments including a moveable table depth, a depth gauge to set the distance the spindle travels and pulley adjustments to change speeds increases the tools functionality. Read more information on v-holdmachinery.com.

After 20 years development, V-HOLD has constructed strong hardware facilities and humanized management system by bringing in tens of brand-new large automotive precision CNC machine center from developed countries such as Japan, German, along with over 67,000m2 large modern workshop with complete facilities and production lines, V-HOLD has realized its high efficient production. Besides that, the cooperation with world famous management consulting firm and introduction of modern business administration system such as ERP, 6S have laid solid foundation to the development of V-HOLD. Thanks for the trust and support of our customer. V-HOLD will consistently stick to the belief that: Profession and concentration accomplish excellent brand !